Mike needs:

  • 9V voltage regulator (5) - jameco doesn't seem to have them. [Digi-key does.](http://rocky.digikey.com/scripts/ProductInfo.dll?Site=US&V=425&M=PQ09RA1)
  • Li 2016 coin cells (4) [jameco part number](http://www.jameco.com/cgi-bin/ncommerce3/ProductDisplay?prmenbr=91&prrfnbr=355233&cgrfnbr=772&ctgys=503;527;772;) (They go for as low as $.50 elsewhere, check [http://www.froogle.com](http://www.froogle.com) - [one source](http://store.yahoo.com/shoppingmatrix2/cr-2016-mxl.html) but shipping probably costs too...)
    • (They're $0.45/1 at Digi-key. CR2032 is the same price. Twice the height, ~2.5x capacity. -m.)
  • Photoresistors. 10? Digi-key has them for cheaper. [one kind.](http://rocky.digikey.com/scripts/ProductInfo.dll?Site=US&V=209&M=PDV-P9007)

Raj needs:

  • flux
  • angle cutters

mang needs:

  • bench power supply
  • IDC cables (10-pin)
    • thanks dodger!
  • IDC cable headers (10-pin, 6-pin)
  • single row 11 pin headers (for RF modules)
  • (more) terminal blocks
  • small slide switches (on - off - strobe)
  • DC/DC converters (MAX1663 or something)
  • surface mount to SIP thingies (surfboard)
  • solid state relays (photomosfet)

  • capacitor assortment

  • C and D cell battery holders (9V snap)

  • hard plastic 9V battery snaps

  • large project boxes for AMB el sequencers
    • Done!
  • CAT5 breakout connectors (telephone stylee)
  • 12V battery clips for charger (Kragen)
  • NPN transistors
  • MOSFETs (IRL320)

  • serial-input parallel-output shift registers (e.g. 74HC409)

  • IC remover
  • IC pin straightener
  • 28-pin sockets (nice ones)
  • random socket assortment
  • 2 position .2" center terminal blocks</S>

  • 8 position .2” center terminal blocks

  • SS copper clad boards
  • adapter so jeweler drills can go in Dremel
  • PCB drill bits
  • Dremel drill press

  • stepper motors

  • DIP clip (tiny programming)

AVR stuff:

  • 6-pin IDC header for ISP
  • AVR 6-pin ISP programmer adapter

  • AVR butterflies

  • ATMega16
  • low profile 16MHz crystals
    • trimmer caps for this xtal

SMT stuff:

  • caps for tiny26 board
  • 0805 resistors for LEDs
  • 1206 resistors
  • 1206 caps
  • 1206 LEDs
  • 8-pin SOIC regulators

  • SMT RGB LEDs

  • water-soluable solder paste
  • plunger
  • syringe
  • vacu-pickup tool?
    • thanks Mike!
  • heat pen for manual work(?)

  • hot-air rework station(?)

  • Holtek encoder/decoder chips (HT-640/HT-648L)

Video stuff:

  • long S-Video cable
  • S-Video dongle for Inspiron
  • BNC video terminators
  • video transmitter?
  • big ass VGA cable
  • long Firewire cable

Audio:

This stuff:
1  	4  	A25915-ND  	CONN HOUSING 6POS .100 DUAL ROW  	    	0  	0.63000  	$2.52
2 	20 	A28328-ND 	CONN SOCKET 22-26AWG 15AU CRIMP 	  	0 	0.07200 	$1.44
3 	20 	311-1.00KFCT-ND 	RES 1.00K OHM 1/4W 1% 1206 SMD 	  	0 	0.08800 	$1.76
4 	10 	311-150ECT-ND 	RES 150 OHM 1/4W 5% 1206 SMD 	  	0 	0.07800 	$0.78

goldmine-elec.com stuff
  	G15293  	 	 Brilliant Green SMD LED by HP (Pkg of 10)  	$0.99  	   	$1.98
	G13706 		Blinding Output Blue SMD LED 	$0.42 	  	$42.00
	G15698 		5.5" x 12" Scissor Cut SS Copper Clad 	$1.75 	  	$3.50
	G15665 		Blue Single Sided 4" x 6" Copper Clad 	$3.49 	  	$13.96
	G2624 		3" x 6" Copper Clad .021" Thick 	$0.55 	  	$2.20
	G2636 		6" x 12" Copper Clad .021" Thick 	$2.15 	  	$4.30
	W22001 		Dual Cat 5 Connector (Pkg of 4) 	$1.00 	  	$2.00
	G13512 		5.5mm DC Power Jack w/ NC Switch (Pkg of 2) 	$1.00 	  	$4.00
	G15664 		Unique Green Neon Lamp (Pkg of 2) 	$1.00 	  	$5.00
	G14781 		KP4M4-029 12VDC Stepper Motor 	$2.95 	  	$5.90

Digikey: Aavid Thermalloy Slide-on heatsink HS179-ND 3A H-Bridge LMD18200T

Interesting parts (not ordering yet):

Jameco Order

Digikey Order

Mouser Order